Appearance

Plastic revetment: choosing materials and construction

Compare plastic with hardwood for revetment along a pond or ditch and consider the complete construction. Prolock Sigma combines plastic panels with supporting posts. Soil, water level, retained height and load determine the panel length, posts and finishing required.

Short answer

Buying plastic revetment: start with size and construction

The Sigma panels in our range are 50 cm wide and differ in length. One straight metre mathematically requires two panels. The full panel length is not the visible retained height: part of the panel goes into the ground. Posts, connections and finishing are determined separately.

Use the Sigma panel calculator for an initial quantity indication and see the materials example for 10 metres. The current price and ordering or quote route are shown for the selected panel size.

The five details needed first

  • Route length, corners and height transitions
  • Visible retained height and water level
  • Known soil conditions or uncertainty about them
  • Loading behind the bank, such as storage or traffic
  • Access and desired installation method

Worked example: two straight sections

A straight section of 6.10 metres requires 13 panels by this calculation; a second section of 2.10 metres requires 5 panels. That makes 18 panels. Rounding only the total length of 8.20 metres would give 17 and would miss the separate rounding for each section.

This initial count uses 0.5 metres of working width per panel, without reusing offcuts. Corner connections, interlocks, end details and cutting losses still need review. The calculator does not determine panel length, posts or anchoring.

Calculate your straight sections

A system rather than a separate product

What do we mean by plastic revetment?

In plastic revetment, plastic forms the visible earth-retaining wall or panel. That panel does not automatically resist all forces by itself. Structural support can be shared between posts, walers, connections and any anchoring.

Prolock Sigma combines relatively short plastic panels with longer, project-specific posts. Prolock Nova uses plastic panels in post-and-panel construction. According to the manufacturer, Omega is intended for heavier sheet-pile constructions. These names are therefore not interchangeable sizes of a single product.

Terms that are often mixed up

Revetment, bank protection or sheet piling?

In everyday searches these words are often used as synonyms. Technically, what matters is the soil and water pressure to resist, how deeply the wall must be embedded and which supporting structure carries the load.

A low pond edge and a heavily loaded quay may have the same bank length but require different constructions. Describe the situation before fixing panel length or post spacing.

From route to materials

How to create an initial product list that can be checked

This sequence prevents a simple panel count from being mistaken for a complete construction.

1

Measure the route

Separate straight sections, internal and external corners, curves and height transitions. Also note where the new revetment connects to an existing construction.

2

Determine the load

Record water level, retained height, indicative soil conditions and use behind the bank. These are inputs for selecting panels, posts, waler and any anchoring.

3

Check all components

Include connections, corners, capping rail or caps, fixings, transport and installation. Only then can you see whether the preliminary list is complete.

Quick orientation

When should you seek further assessment first?

Light bank, clear details

Sigma may be a sensible option to investigate for limited earth retention along a pond, ditch or small watercourse. Even then, posts, soil and load remain part of the assessment.

Buy Prolock Sigma: sizes and components

Post-and-panel appearance or renovation

According to the manufacturer, Nova combines plastic panels with timber or hardwood posts. DamwandDirect treats Nova as a project enquiry and does not publish an invented online price or stock status.

Compare Prolock systems

Greater or uncertain load

Greater retained heights, unknown soil, traffic, heavy storage, anchoring or complex connections require technical assessment before product selection.

View the project checklist

Frequently asked questions

Answers about plastic revetment

What is plastic revetment?

Plastic revetment is an earth-retaining bank construction in which plastic panels form part of the visible wall. The complete construction may also include posts, walers, fixings, finishing components and anchoring.

How many Prolock Sigma panels are needed per metre?

The Sigma panels in the current DamwandDirect range have a working width of 0.5 metres. One straight metre therefore requires two panels mathematically. This is only an initial quantity indication; corners, connections, height differences, posts and finishing are determined separately.

Is plastic revetment suitable for every waterfront?

No. Retained height, soil, water level, load and supporting structure determine whether Sigma, another Prolock option, hardwood or a project-specific design is appropriate. If in doubt, technical assessment is needed before choosing materials.

Do I need a permit for plastic revetment?

This can differ by location, water authority and construction. Before ordering, run the Dutch Vergunningcheck in the Omgevingsloket and contact the municipality, water authority or other competent body if in doubt.

Next step

Also compare plastic with hardwood

A materials comparison is only fair when the plastic panels, posts, hardwood alternative, fixings, finishing and transport are compared for the same project conditions.

Verifiable sources

Sources for this page

The links below support the factual information. Manufacturer sources remain clearly identified; check local rules with the competent authority. Linked external original sources are in Dutch and government sources concern the Netherlands.